| |
| |

| | | | | |

|

EE TIMES NETWORK

Online Editions
EE TIMES
EE TIMES ASIA
EE TIMES CHINA
EE TIMES FRANCE
EE TIMES GERMANY
EE TIMES INDIA
EE TIMES JAPAN
EE TIMES KOREA
EE TIMES TAIWAN
EE TIMES UK

EE TIMES EUROPE
ANALOG EUROPE
INDUSTRIAL EUROPE
AUTOMOTIVE DL EUROPE

POWER DL EUROPE

Web Sites
• Audio DesignLine
• Automotive DesignLine
• Career Center
• CommsDesign
• Microwave
Engineering
• Deepchip.com
• Design & Reuse
• Digital Home DesignLine
• DSP DesignLine
• EDA DesignLine
• Embedded.com
• Elektronik i Norden
• Green SupplyLine
• Industrial Control
DesignLine
• Planet Analog
• Mobile Handset
DesignLine
• Power Management
DesignLine
• Programmable Logic
DesignLine
• RF DesignLine
• RFID-World
• Techonline
• Video | Imaging
DesignLine
• Wireless Net
DesignLine

ELECTRONICS GROUP SITES

• eeProductCenter
• Electronics Supply &
Manufacturing
• Conferences
and Events
• Electronics Supply &
Manufacturing--China
• Electronics Express
• Webinars

22 September 2009
SIGNAL CHAIN BASICS Series (Part 4): Introduction to analog/digital converter (ADC) types

The SIGNAL CHAIN BASICS series continues with this Introduction to analog/digital converter types

By Bill Klein, Senior Applications Engineer, Texas Instruments
Planet Analog
December 14, 2007 (2:41 PM EST)

| Rate this article |

WORSE | BETTER
| | | |
1 | 2 | 3 | 4 | 5
| |
| |

(Editor's Note: There are links to the previous parts of this series at the end, below the author's biography.)

Many circuit designs have been tried in the development of analog-to-digital converters (ADC). The field has been narrowed to four basic topologies: flash, successive-approximation (SAR), pipeline, and sigma-delta converters. Each has its strong and weak points.

The optimum device for a particular system depends on the application. More specifically, the optimum device depends on what needs to be done with the data. Applications requiring waveform reconstruction have different requirements from those applications performing calculations or decisions based on a snapshot reading.

The speed-resolution comparison between the four most popular converter types is shown in Figure 1. As new circuit techniques are developed, the performance boundaries between them have become somewhat blurred.

Figure 1: ADC type comparison
(Click on image to enlarge)

Beyond the speed-resolution distinction, the next performance point is time-of-reading. The flash converter is a very high-speed device, and time synchronization usually is not an issue. In contrast, the SAR converter uses a start-convert signal. With this capability, two or more devices can be synchronized to an external event. The data appears several clock cycles following the convert command.

Both the pipeline and sigma-delta topology converters are continuous-conversion devices. This makes it nearly impossible to synchronize multiple devices for simultaneous reading, or to obtain a snapshot reading at a defined moment. There will be a time lapse between an event at the analog input and the appearance of that event in the digital data stream. That time delay is termed data latency.

Data latency should not to be confused with the conversion time associated with the SAR converter, where there are no other conversion operations in progress. Sigma-delta converters can be compared to performing a running average. The pipeline converter, however, can be compared to an assembly line. After a station contributes to the final result, the signal moves on, making way for that station to process the next sample.

One result of this difference is that sigma-delta converters effectively transpose noise energy to frequency bands above the frequencies of interest. Pipeline-style converters accomplish high data rates with moderate-to-high resolution.

Another significant change brought about by the new techniques is the disappearance of the stand-alone sample-and-hold (S/H) amplifier. To obtain a valid conversion results, the analog input must be stable to within less than one least significant bit (LSB) during the conversion time. Several advancements in converter performance including increased resolution, shorter conversion times, and reduced full-scale voltage, all point to the need for higher-performance S/H amplifiers. Advanced circuit topology has allowed the S/H amplifier to be built into the converter.

Each of these converter types will be investigated in detail in future articles.

About the author

William P. (Bill) Klein is a Senior Applications Engineer with the High Performance Analog group at Texas Instruments. Bill joined TI through its acquisition of Burr-Brown in August 2000. His experience as an analog circuit designer covers over 40 years in fields ranging from mineral exploration to medical nuclear imaging. One current role Bill has is hosting the Analog e-LAB Web Cast, presenting real world solutions to real world problems in analog circuit design. In addition to a BSEE from Arizona State University and registration as a Professional Engineer in the State of Arizona, he has authored numerous magazine articles, application notes and conference papers.

Previous installments of this series:

"SIGNAL CHAIN BASICS Series (Part 3): Analog and the digital world", www.planetanalog.com/features/showArticle.jhtml;?articleID=204400376, click here
"SIGNAL CHAIN BASICS Series (Part 2): Op Amp--Basic operations", www.planetanalog.com/features/showArticle.jhtml;?articleID=203101699, click here
"SIGNAL CHAIN BASICS: Operational Amplifier--The Basic Building Block", www.planetanalog.com/features/showArticle.jhtml;?articleID=202801320, click here

Increase Efficiency and Save Space in Power Supplies. Fairchild's highly integrated FPS™ power switch, the FSFM300, can handle up to 30W of output power without a heatsink, reducing board space and costs. Learn more.

EE Times TechCareers

Search Jobs

Enter Keyword(s):

Function:

Engineering & Arch.

Information Tech.

State:

Post Your Resume
-----------------
Employers Area

Most Recent Posts
BAE Systems seeking Director-Architecture in Herndon, VA
SEL seeking Business Development Manager in Alexandria, VA
ITT Systems seeking System Administrator in IQ, Middle East
ITT Systems seeking Supply Clerk/Tech in IQ, Middle East
AWR Corp seeking Microwave Library Development Engr in El Segundo, CA
More career-related news, resources and job postings for technology professionals

Sponsor Links

45V, 50mA Synchronous Buck Converter with Only 12µA Quiescent Current
Linear's LTC®3642, a 45V input capable synchronous buck converter, can deliver up to 50mA of continuous output current from a 3mm x 3mm (or MSOP8-E) package. It operates from an input voltage range of 4.5V to 45V (60V Max), making it ideal for automotive & industrial 4mA to 20mA control loop applications. For more information, visit here

Watch the latest videos from Fairchild covering topics on power supply and portable applications.

Industry's smallest 16-bit ADC - Get samples and evaluation modules today! Click for more information.

All materials on this site Copyright © 2009 TechInsights, a Division of United Business Media LLC.
All rights reserved.
Terms and Conditions | Privacy Statement | Your California Privacy Rights

|