Flyback converter

From Wikipedia, the free encyclopedia

Jump to: navigation, search

The Flyback converter is a DC to DC converter with a galvanic isolation between the input and the output(s). More precisely, the flyback converter is a buck-boost converter with the inductor split to form a transformer, so that the voltage ratios are multiplied with an additional advantage of isolation. When driving for example a plasma lamp or a voltage multiplier the rectifying diode of the Buck-Boost converter is left out and the device is called a flyback transformer. Due to intrinsic limitations, this converter is only used in low power applications (up to about 250 W).[citation needed]

Contents

1 Structure and principle
2 Operation
3 Limitations
4 Applications

[edit] Structure and principle

Fig. 1: Schematic of a flyback converter.

The schematic of a flyback converter can be seen in figure 1. It is equivalent to that of a buck-boost converter, with the inductor split to form a transformer . Therefore the operating principle of both converters is very close:

When the switch is on (see figure 2), the primary of the transformer is directly connected to the input voltage source. This results in an increase of magnetic flux in the transformer. The voltage across the secondary winding is negative, so the diode is reverse-biased (i.e blocked). The output capacitor supplies energy to the output load.
When the switch is off, the energy stored in the transformer is transferred to the output of the converter.

[edit] Operation

The two configurations of a flyback converter in operation: In the on-state, the energy is transferred from the input voltage source to the transformer (the output capacitor supplies energy to the output load). In the off-state, the energy is transferred from the transformer to the output load (and the output capacitor).

The flyback converter is an isolated power converter, therefore the isolation of the control circuit is also needed. The two prevailing control schemes are voltage mode control and current mode control. Both require a signal related to the output voltage. There are two common ways to generate this voltage. The first is to use an optocoupler on the secondary circuitry to send a signal to the controller. The second is to wind a separate winding on the coil and rely on the cross regulation of the design.

The flyback is often used in multiple output circuits because of the cost-effective regulation of multiple outputs. By holding one output at a constant voltage, and transferring current, whichever output is lowest (relative to the turns ratio of the transformer) will receive the most current, bringing it back up in voltage. When an output is too high, it receives less current, and the loading brings it back down.

Fig. 3:Waveforms of current and voltage in a flyback converter operating in continuous mode.

Fig. 4:Waveforms of current and voltage in a flyback converter operating in discontinuous mode.

[edit] Limitations

Similar to a buck-boost converter the switch in the primary circuit must withstand higher voltages than originally applied to the primary.The amount of voltage it has to withstand is

Where Vp=voltage applied to primary
N1=number of turns in primary
N2=number of turns in secondary
d=duty ratio of switch

In contrast to the buck-boost converter and to the autotransformer, leakage inductance just increases this voltage without increasing the secondary voltage. In contrast to push-pull converters a core with an air gap is needed.

Discontinuous mode has the following disadvantages:

High RMS and peak currents in the design
High flux excursions in the inductor

These limit the efficiency of the converter.

Continuous mode has the following disadvantages:

The Voltage feedback loop requires a lower bandwidth due to a zero in the response of the converter.
The Current feedback loop used in current mode control needs slope compensation in many cases.
The power switches are now turning on with positive current flow.

These complicate the control of the converter.

[edit] Applications

Low-power switch-mode power supplies (cell phone charger, standby power supply in PCs, main PC supplies < 250 W)
High voltage supply for the CRT in TVs and monitors (the flyback converter is often combined with the horizontal deflection drive).
High voltage generation, e.g. for Xenon flash lamps, lasers, copiers etc.
The ignition system in Spark-Ignition engines is also a flyback converter, the ignition coil being the transformer and the contact breaker forming the switch element.
Isolated gate driver.
Low cost multiple-output power supplies.

Retrieved from "http://en.wikipedia.org/wiki/Flyback_converter"

Categories: Electrical power conversion

Hidden categories: All articles with unsourced statements | Articles with unsourced statements since January 2008

Views

Article
Discussion
Edit this page
History

Personal tools

Log in / create account

Navigation

Main Page
Contents
Featured content
Current events
Random article

Interaction

About Wikipedia
Community portal
Recent changes
Contact Wikipedia
Donate to Wikipedia
Help

Search

Toolbox

What links here
Related changes
Upload file
Special pages
Printable version
Permanent link
Cite this page

Languages

Deutsch
Español
Français
Lëtzebuergesch
Русский

This page was last modified on 26 March 2008, at 21:00.
All text is available under the terms of the GNU Free Documentation License. (See Copyrights for details.)
Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a U.S. registered 501(c)(3) tax-deductible nonprofit charity.

Privacy policy
About Wikipedia
Disclaimers