Boost converter

From Wikipedia, the free encyclopedia

Jump to: navigation, search

A boost converter (step-up converter) is a power converter with an output dc voltage greater than its input dc voltage. It is a class of switching-mode power supply (SMPS) containing at least two semiconductor switches (a diode and a transistor) and at least one energy storage element. Filters made of inductor and capacitor combinations are often added to a converter’s output to improve performance.

The basic schematic of a boost converter. The switch is typically a MOSFET, IGBT, or BJT.

Contents

1 Overview
2 History
3 Applications
4 Circuit analysis

4.1 Operating principle

4.1.1 Continuous mode
4.1.2 Discontinuous mode

5 See also
6 References
7 External links

[edit] Overview

An a.c. mains voltage cannot directly power devices such as computers, digital clocks, and telephones. The outlet supplies AC and the devices and loads require DC. Power conversion enables DC devices to utilize power from ac voltage sources. A process called ac to dc conversion (rectification) is used to convert an AC voltage to power a DC load.

Power can also come from DC sources such as batteries, solar panels, rectifiers, and DC generators. A process that changes one DC voltage to a different DC voltage is called dc to dc conversion. A boost converter is a DC to DC converter with an output voltage greater than the source voltage. A boost converter is sometimes called a step-up converter since it “steps up” the source voltage. Since power (V*I) must be conserved, the output current is lower than the source current.

[edit] History

For high efficiency, the SMPS switch must turn on and off quickly and have low losses. The advent of a commercial semiconductor switch in the 1950’s represented a major milestone that made SMPSs such as the boost converter possible. Semiconductor switches turned on and off more quickly and lasted longer than other switches such as vacuum tubes and electromechanical relays. The major DC to DC converters were developed in the early-1960s when semiconductor switches had become available. The aerospace industry’s need for small, lightweight, and efficient power converters led to the converter’s rapid development.

Switched systems such as SMPS are a challenge to design since its model depends on whether a switch is opened or closed. R.D. Middlebrook from Caltech in 1977 published the models for DC to DC converters used today. Middlebrook averaged the circuit configurations for each switch state in a technique called state-space averaging. This simplification reduced two systems into one. The new model led to insightful design equations which helped SMPS growth.

[edit] Applications

Battery powered systems often stack batteries in series to achieve higher voltage. However, stacking batteries is not possible in many high voltage applications due to lack of space. Boost converters can increase the voltage and reduce the number of cells. Two battery-powered applications that use boost converters are hybrid electric vehicles (HEV) and lighting systems.

The Toyota Prius HEV contains a motor which utilizes voltages of approximately 500 V. Without a boost converter, the Prius would need nearly 417 batteries to power the motor. However, a Prius actually uses only 168 batteries and boosts the battery voltage from 202 V to 500 V. Boost converters also power devices at smaller scale applications, such as portable lighting systems. A white LED typically requires 3.3V to emit light, and a boost converter can step up the voltage from a single 1.5 V alkaline cell to power the lamp. Boost converters can also produce higher voltages to operate cold cathode fluorescent tubes (CCFL) in devices such as LCD backlights and some flashlights.

[edit] Circuit analysis

[edit] Operating principle

Fig. 1:Boost converter schematic

Fig. 2: The two configurations of a boost converter, depending on the state of the switch S.

The basic principle of a Boost converter consists in 2 distinct states (see figure 2):

in the On-state, the switch S (see figure 1) is closed, resulting in an increase in the inductor current;
in the Off-state, the switch is open and the only path offered to inductor current is through the flyback diode D, the capacitor C and the load R. This results in transferring the energy accumulated during the On-state into the capacitor.

[edit] Continuous mode

Fig. 3:Waveforms of current and voltage in a boost converter operating in continuous mode.

When a boost converter operates in continuous mode, the current through the inductor (IL) never falls to zero. Figure 3 shows the typical waveforms of currents and voltages in a converter operating in this mode. The output voltage can be calculated as follows, in the case of an ideal converter (i.e using components with an ideal behaviour) operating in steady conditions:

During the On-state, the switch S is closed, which makes the input voltage (Vi) appear across the inductor, which causes a change in current (IL) flowing through the inductor during a time period (t) by the formula:

At the end of the On-state, the increase of IL is therefore:

D is the duty cycle. It represents the fraction of the commutation period T during which the switch is On. Therefore D ranges between 0 (S is never on) and 1 (S is always on).

During the Off-state, the switch S is open, so the inductor current flows through the load. If we consider zero voltage drop in the diode, and a capacitor large enough for its voltage to remain constant, the evolution of IL is:

Therefore, the variation of IL during the Off-period is:

As we consider that the converter operates in steady-state conditions, the amount of energy stored in each of its components has to be the same at the beginning and at the end of a commutation cycle. In particular, the energy stored in the inductor is given by:

Therefore, it is obvious that the inductor current has to be the same at the beginning and the end of the commutation cycle. This can be written as

Substituting and by their expressions yields:

This can be written as:

Which in turns reveals the duty cycle to be:

From the above expression it can be seen that the output voltage is always higher than the input voltage (as the duty cycle goes from 0 to 1), and that it increases with D, theoretically to infinity as D approaches 1. This is why this converter is sometimes referred to as a step-up converter.

[edit] Discontinuous mode

Fig. 4:Waveforms of current and voltage in a boost converter operating in discontinuous mode.

In some cases, the amount of energy required by the load is small enough to be transferred in a time smaller than the whole commutation period. In this case, the current through the inductor falls to zero during part of the period. The only difference in the principle described above is that the inductor is completely discharged at the end of the commutation cycle (see waveforms in figure 4). Although slight, the difference has a strong effect on the output voltage equation. It can be calculated as follows:

As the inductor current at the beginning of the cycle is zero, its maximum value (at t=D.T) is

During the off-period, IL falls to zero after δ.T:

Using the two previous equations, δ is:

The load current Io is equal to the average diode current (ID). As can be seen on figure 4, the diode current is equal to the inductor current during the off-state. Therefore the output current can be written as:

Replacing ILmax and δ by their respective expressions yields:

Therefore, the output voltage gain can be written as:

Compared to the expression of the output voltage for the continuous mode, this expression is much more complicated. Furthermore, in discontinuous operation, the output voltage gain not only depends on the duty cycle, but also on the inductor value, the input voltage, the switching frequency, and the output current.

[edit] See also

Buck Converter

Buck-Boost Converter

[edit] References

Mohan, Ned; Undeland, Tore M., Robbins, William P. (2003). Power Electronics. Hoboken: John Wiley & Sons, Inc.. ISBN 0-471-42908-2.

Basso, Christophe (2008). Switch Mode Power Supplies: SPICE Simulations and Practical Designs. New-York: McGraw-Hill. ISBN 0071508589.

[edit] External links

Boost PFC Mathematical Calculations
Daycounter Switching Converter Power Supplies

Retrieved from "http://en.wikipedia.org/wiki/Boost_converter"

Categories: Electrical power conversion

Views

Article
Discussion
Edit this page
History

Personal tools

Log in / create account

Navigation

Main Page
Contents
Featured content
Current events
Random article

Interaction

About Wikipedia
Community portal
Recent changes
Contact Wikipedia
Donate to Wikipedia
Help

Search

Toolbox

What links here
Related changes
Upload file
Special pages
Printable version
Permanent link
Cite this page

Languages

Deutsch
Español
Français
Italiano

This page was last modified on 9 April 2008, at 17:42.
All text is available under the terms of the GNU Free Documentation License. (See Copyrights for details.)
Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a U.S. registered 501(c)(3) tax-deductible nonprofit charity.

Privacy policy
About Wikipedia
Disclaimers